機械畢業設計外文翻譯--巖土材料的摩擦聲波

1、<p><b>　　中文3280字</b></p><p>　　畢業設計（論文）外文資料翻譯</p><p>　　學院： 機械工程學院 </p><p>　　專業： 機械設計制造及其自動化 </p><p>　　班級：

2、 </p><p>　　姓名： </p><p>　　學號： </p><p>　　外文出處： Tyler T J, Hill R, Lai E. Friction gene

3、rated ultrasound from geotechnical materials[J]. Ultrasonics, 2004, 42(1): 169-172. </p><p>　　附 件：1、外文原文；2、外文資料翻譯譯文。</p><p><b>　　附件1：</b></p><p>　　Friction

4、generated ultrasound from geotechnical materials</p><p>　　TJ Tyler, R Hill, E Lai</p><p><b>　　Abstract</b></p><p>　　Drilling is a process involved with product manufactu

5、ring and for civil engineers, site preparation. The usual requirement is for efficient material removal. In this study, the friction pair interaction generated by a drilling process provides ultrasound information relate

6、d to parameters for the geotechnical material being drilled, where the drill bit has non-degrading ultrasonic characteristics and no essential requirement for material removal. This study has considered monitoring the ul

7、trasoni</p><p>　　Introduction </p><p>　　The ultrasound generated from a solid–solid friction pair has been the main focus of research concerning friction-generated ultrasound, mainly associated

8、with rotating and reciprocating machines. A frictional process developed during relative movement between contacting materials has an inherent level of wear that eventually would result in failure. Monitoring the ultraso

9、nic signal generated from machinery has become an alternative condition-monitoring tool, as the generated signal contains info</p><p>　　relationship between the AERMS and the sliding velocity. Jiaa and Dornf

10、ield [4] monitored the AE generated by a pin on disk experiment, highlighting that the AE is caused by impulsive shock due to asperity collisions and micro-vibrations excited by stick–slip phenomena. The research shows t

11、hat the AERMS increases with load while a linear relationship exists between the relative surface velocity and the AERMS. Sarychev and Shchavelin [5] describe the frictional process and the generated acoustic </p>

12、<p>　　The general rule for the dependence of the count rate N_ on the sliding velocity is in the form: N_ A t BvX e2T where A and B are constants and X P1. A similar relationship also applies for the dependence o

13、f the load on the count rate, but the exponent X 61. A further relationship was expressed relating the AE activity to the regime of friction in elastic contact: N_ a k N0:71h0:71A0:71 c r0:90R1:60 a V e3T where N is the

14、 normal load, h the generalised elastic modulus, Ac the counter area of </p><p>　　Current studies in friction-generated acoustics have shown that the acoustic signals contain information relating to the mate

15、rial parameters of the friction pair. The work in this study uses the acoustic signal as a tool to characterise the material properties of the friction pair. The idea for this study originates from a study by Hill [8] fo

16、r Scientifics, when it became apparent that monitoring the ultrasound generated by a drilling process process had potential for ground condition monitoring</p><p>　　2. Experimental design</p><p>

17、;　　A simplified drilling arrangement has been constructed where a rotating probe is used to maximise the friction at the probe-tip–granular contact. The probe string is designed, using a suitable coupling device, so tha

18、t the ultrasonic signal is transmitted from the probe tip to a stationary piezoelectric sensor. The signal is amplified by 60 dB and filtered between 250 and 500 kHz. The captured signal is therefore in the mid-ultrasoni

19、c range and relates to the transducer monitoring frequency used</p><p>　　3. Results</p><p>　　The effect of load on the count rate can be seen in Fig. 2a. The signal values on the left of the fig

20、ure correspond to the probe tip not being in contact with the granular medium. When the probe is pushed into the granular material the load increases. The data highlights a stabilizatio(reduction) in the count rate and i

21、s referred to as the ‘‘characteristic count rate’’ for a particular friction pair. The stabilisation of the count rate means that no more oscillations are being produced due to an</p><p>　　different particle

22、 sizes still exist. Results have revealed that the count rate value does not significantly change due to the addition of water and that the count ratesignal is mainly dependent on the number of contacts formed. Therefore

23、, regardless of the water content of the sand it is possible to obtain an approximate evaluation of the average particle size.</p><p>　　The ultrasonic signal energy appears to be sensitive to a number of par

24、ameters including the particle size, water content, density and mineralogy. Fig. 3a shows the ultrasonic energy signal plotted against the applied force for two different initial dry densities (compacted and loose). Resu

25、lts indicate that the energy varies linearly with the applied load and the gradient increases with a reduction in the initial density. The effect of varying the density is more apparent when using smaller grai</p>

26、<p>　　The effect of increasing the water content of the granular sample causes the sand to become acoustically quieter (a significant drop in signal amplitude). Although the sand becomes quieter, the rate of chang

27、e of the ultrasonic energy due to the applied force is not affected by varying the level of water content in a wet sample but there is a noticeable difference in the gradient when comparing a dry sample with a wet sample

28、.</p><p>　　4. Conclusions</p><p>　　Results have shown that when probing into granular materials, using a constant sliding velocity the count rate becomes stable (characteristic count rate). The

29、characteristic count rate is affected by a change in the number probe–granular contacts and therefore provides a method for characterising the particle size. The water content of a granular sample has little effect on th

30、e characteristic count rate and data agrees with the assumption stated by Baranov et al. [6] that the count rate is propo</p><p>　　The ultrasonic energy signal is sensitive to a variety of parameters includi

31、ng the load, sliding velocity, particle size, density, water content and mineralogy. Results have indicated that the contact pressure, which is affected by altering the density and particle size, affects the acoustic ene

32、rgy signal. However, a continuous increase in the ultrasonic energy due to larger particle sizes, which was expected, did not occur. It is possible that larger particles produce larger particle-probe cont</p><

33、p>　　References</p><p>　　[1] T.J. Holroyd, N. Randall, Use of acoustic emission for machine condition monitoring, Condition Monitoring 35 (2) (1993) 75–79.</p><p>　　[2] S.T.S. Bukkapatnam, S.R

34、.T. Kumara, A. Lakhtakia, Analysis of acoustic emission signals in machining, ASME Journal of Manufacturing Science and Engineering (1999) 183–207.</p><p>　　[3] E.N. Diei, Acoustic emission sensing of tool w

35、ear in face milling, Journal of Engineering for Industry 109 (1987) 234–240.</p><p>　　[4] C.L. Jiaa, D.A. Dornfield, Experimental studies of sliding friction and wear via acoustic emission signal analysis, W

36、ear 139 (1990) 403–424.</p><p>　　[5] G.A. Sarychev, V.M. Shchavelin, Acoustic emission method for research and control of friction pairs, Tribology International 24 (1) (1991) 11–16.</p><p>　　[6

37、] V.M. Baranov, E.M. Kudryavtsev, G.A. Sarychev, Calculation of the parameters of acoustic emission when there is external friction between solids, Russian Journal of Non-Destructive Testing 8 (1995) 569–577.</p>

38、<p>　　[7] C. Henrique, M.A. Aguirre, A. Calvo, I. Ippolito, D. Bideau, Experimental acoustic technique in granular flows, Powder Technology94 (1997) 85–89.</p><p>　　[8] R. Hill, Confidential consultancy

39、 Report, Scientifics, 1997.</p><p><b>　　附件2：</b></p><p><b>　　巖土材料的摩擦聲波</b></p><p><b>　　摘要</b></p><p>　　鉆井作業涉及到設備生產，對于工程師來說，還包括地址的選擇。

40、鉆井通常要求高效地去除材料。在這項研究中，鉆井過程中摩擦副的相互作用提供了被鉆削巖土材料相關參數的超聲信息，在這些信息中鉆頭具有非降解的超聲特性，對于材料去除沒有基本的要求。這項研究認為監測鉆井過程中產生的超聲波信號，為表征巖土材料鉆削參數提供了新的觀點，并提供了一種識別或表征地面結構的新方法。巖土材料系統的鉆削，通常涉及一個旋轉探頭和顆粒復合介質的相互作用。測量旋轉探頭的載荷和角速度可用來確定它們和超聲信號的相關性。顆粒材料的樣本已經

41、把粒徑控制在一定范圍內。精力主要集中在確定晶粒尺寸、堆積密度和顆粒材料的含水量對超聲信號的影響。將不同粒徑、密度、水分含量和相關超聲波信號的顆粒樣本進行比較，解釋每個變量的影響和有關這種影響的現有理論。這項研究一般的目的是評估鉆井的超聲監測，并估計其在巖土地表實時狀態監測中的應用潛力，用它來代替現有的一些方法。</p><p><b>　　1.引言</b></p><p&

42、gt;　　固體–固體摩擦副產生的超聲波是摩擦產生超聲波研究的重點，主要涉及旋轉和往復運動的機械。相互接觸的材料相對運動過程中的摩擦產生固有的磨損，最終會導致工作故障。監測機械產生的超聲波信號已成為一種不可替代的機器狀態監測方法，因為超聲波信號包含了與摩擦副的微觀環境相關的信息。當機器零件發生磨損時，用這種方法來查明故障是可行的，因而降低了因災難性故障導致生產停機所帶來的風險。Holroyd和 Randall [ 1 ]論述了利用聲音輻射

43、技術（AE）檢測潤滑、超載、磨損變化的靈敏度問題，并查閱了許多其他用于分析聲學特征的技術。Bukkapatnam等人[ 2 ]論述了用于分析摩擦聲信號更先進的方法，并提出了一種基于混沌理論、小波和神經網絡的新的分析技術。大多數有關狀態監測的研究更關注由磨損引起的聲信號變化，而一些研究也已經注意到與產生聲信號相關的參數。Diei [3]監測了表面磨削過程中刀具磨損所產生的聲音輻射，提出了AERMS電壓和摩擦能量耗散率之間的冪函數關系 ek

44、gssAaV Tm=2 e1T 。其中k和m取決于聲音輻射測量系統和摩擦副材料性能常數；g是摩擦副的表面粗糙度和彈性度的函數；s</p><p>　　目前摩擦聲學研究已經表明聲音信號包含了與摩擦副材料參數相關的信息。這項研究工作用聲信號作為一種表征摩擦副材料特性的工具。當監測鉆井過程中產生的超聲波對地面狀態監測的作用變得明顯的時候，這種思想在Hill[ 8 ]為Scientifics所做的一項研究中產生了。這項

45、工作的總體目標是研究一種利用典型鉆井過程并監測鉆頭和巖土材料相互作用產生的超聲波來描述巖土材料特性的方法。</p><p><b>　　實驗設計</b></p><p>　　一個簡單的鉆井裝置具有一個使探針–顆粒接觸面積最大化的旋轉探頭。使用合適的耦合裝置設計探頭串，使超聲波信號從探頭傳輸?shù)揭粋€固定的壓電傳感器。該信號被放大了60分貝并過濾掉250和500千赫之間的信

46、號。因此所得到的信號在中超聲波的范圍內并與所使用傳感器的監測頻率有關。實驗裝置示意圖如圖1所示。探頭伸入具有一定粒徑、初始密度和含水量的顆粒介質中旋轉。探頭的進給速度和角速度設置為一定值，并同時監測所施加的載荷、計數率和超聲波能量。粒徑、密度和含水量對兩種超聲參數（計數率和能量）的影響被進行了研究，這種研究的目的是為未來地面狀態監測提供一種選擇。</p><p><b>　　實驗結果</b>

47、</p><p>　　載荷對于計數率的影響如圖2a所示。位于圖左側的信號數值對應不與顆粒介質接觸的探針。當探頭推入顆粒材料時，負載隨之增加。對于計數率模型，所得數據要求穩定可靠（原始），并將之稱為一個特定摩擦副的“特征計數率”。計數率的穩定意味著負載的增加不會產生更多的震蕩，因此信號幅度只受振幅增加的影響。實驗中使用了不同等級的顆粒材料，并且其特征計數率也已被監測。 研究結果表明，隨著平均粒徑的增大特征計數率會降

48、低。在圖2b中，對八份沙子樣本進行了特征計數率與粒徑的比較。粒徑越大，接觸面積就越小。因此實驗結果印證了Baranov等人[ 6 ]提出的計數率與單位時間內接觸次數成正比的假設。在圖2c中，實驗結果表明含水量對特征計數率影響不大。使用四種不同尺寸的晶粒，畫出計數率與質量含水率的關系曲線。盡管計數率發生很小的變化，但是不同粒徑產生的信號分離仍然存在。實驗結果表明，增加水含量不會引起計數率地顯著變化，計數率信號主要取決于產生接觸的次數。因此

49、，無論沙子含水量多少，都可以獲得其平均粒度的近似計算。</p><p>　　超聲波信號的能量似乎對包括顆粒大小、含水量、密度和礦物質含量在內的一些參數很敏感。圖3a顯示出超聲波能量信號與施加在兩份不同初始干密度（松散與密實）樣本上的力的關系曲線。實驗結果表明，超聲波信號的能量與施加的荷載線性相關，相關線的斜率隨樣本初始密度的降低而增加。當使用較小的晶粒尺寸時，密度變化對超聲波信號能量的影響更為顯著。使用粒徑更小的

50、顆粒材料時，密度的變化將對表面接觸區中探針–顆粒接觸次數產生更大的影響。較低的顆粒密度產生更少的接觸，因而荷載產生的壓力增大，并可能使荷載的函數——平均每振蕩的能量增加。預計由于較高的接觸壓力顆粒尺寸的增加也會使超聲波能量增加。圖3b顯示了由于對平均粒徑施加力而引起平均每振蕩能量的變化。結果表明在粒徑達到512 lm時超聲波能量參數和粒徑之間沒有特殊的關系。</p><p>　　增加顆粒樣本的含水量導致沙子變得更

51、安靜（聲信號幅值顯著下降）。雖然沙子變得更安靜，在潮濕的沙子樣本中因施力產生的超聲波能量的變化率不受水含量變化的影響，但是當把干燥的樣本與潮濕的樣本進行比較時，它們在聲波梯度上仍有明顯的差異。</p><p><b>　　結論</b></p><p>　　實驗結果表明，用一個恒定的滑動速率探查顆粒材料時，計數率趨于穩定（特征計數率）。特征計數率受到探針–顆粒接觸次數的

52、影響，從而提供了一種用于表征顆粒粒徑的方法。顆粒樣本的含水量對特征計數率幾乎無影響。而且實驗所得數據印證了Baranov等人[ 6 ]所提出的計數率與單位時間內接觸次數成正比的假設。然而，實驗所得數據不符合Sarychev和shchavelin [ 5 ]提出的一般規律，因為特征計數率不依賴于所施加的力。實驗結果提供了有力的證據來表明監測特征計數率具有實現不依賴水分含量而識別地面結構不同粒度層的潛力。</p><p&

53、gt;　　超聲波能量信號對于包括負載、滑動速率、粒徑、密度、含水量和礦物質含量在內的多種參數很敏感。實驗結果表明受密度和粒徑變化影響的接觸壓力會影響聲波能量信號。然而，在意料之中，由于更大的顆粒尺寸而引起超聲波能量持續地增加不會發生。較大的顆粒產生較大的粒子-探頭接觸面積從而減小單一接觸點的接觸壓力是可能的，但需進一步研究來支持這種觀點。很明顯，超聲波能量包含了與摩擦副參數相關的信息，但是為了完全了解與產生聲音信號相關的每個參數的分布，

54、還需要做進一步的研究。</p><p><b>　　參考文獻</b></p><p>　　[1] T.J. Holroyd, N. Randall, Use of acoustic emission for machine condition monitoring, Condition Monitoring 35 (2) (1993) 75–79.</p>

55、<p>　　[2] S.T.S. Bukkapatnam, S.R.T. Kumara, A. Lakhtakia, Analysis of acoustic emission signals in machining, ASME Journal of Manufacturing Science and Engineering (1999) 183–207.</p><p>　　[3] E.N. D

56、iei, Acoustic emission sensing of tool wear in face milling, Journal of Engineering for Industry 109 (1987) 234–240.</p><p>　　[4] C.L. Jiaa, D.A. Dornfield, Experimental studies of sliding friction and wear

57、via acoustic emission signal analysis, Wear 139 (1990) 403–424.</p><p>　　[5] G.A. Sarychev, V.M. Shchavelin, Acoustic emission method for research and control of friction pairs, Tribology International 24 (1

58、) (1991) 11–16.</p><p>　　[6] V.M. Baranov, E.M. Kudryavtsev, G.A. Sarychev, Calculation of the parameters of acoustic emission when there is external friction between solids, Russian Journal of Non-Destructi

59、ve Testing 8 (1995) 569–577.</p><p>　　[7] C. Henrique, M.A. Aguirre, A. Calvo, I. Ippolito, D. Bideau, Experimental acoustic technique in granular flows, Powder Technology94 (1997) 85–89.</p><p>