版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領
文檔簡介
1、Journal of Materials Processing Technology 142 (2003) 692–696Tensile properties and fracture locations of friction-stir-welded joints of 2017-T351 aluminum alloyH.J. Liu a,b,?, H. Fujii a, M. Maeda a, K. Nogi aa Joining
2、and Welding Research Institute, Osaka University, Osaka 567-0047, Japan b National Key Laboratory of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin 150001, PR ChinaReceived 30 October 2002
3、; received in revised form 15 May 2003; accepted 5 June 2003AbstractFriction stir welding (FSW) is a new and promising welding process that can produce low-cost and high-quality joints of heat-treatable aluminum alloys b
4、ecause it does not need consumable filler materials and can eliminate some welding defects such as crack and porosity. In order to demonstrate the friction stir weldability of the 2017-T351 aluminum alloy and determine o
5、ptimum welding parameters, the relations between welding parameters and tensile properties of the joints have been studied in this paper. The experimental results showed that the tensile properties and fracture locations
6、 of the joints are significantly affected by the welding process parameters. When the optimum revolutionary pitch is 0.07 mm/rev corresponding to the rotation speed of 1500 rpm and the welding speed of 100 mm/min, the ma
7、ximum ultimate strength of the joints is equivalent to 82% that of the base material. Though the voids-free joints are fractured near or at the interface between the weld nugget and the thermo-mechanically affected zone
8、(TMAZ) on the advancing side, the fracture occurs at the weld center when the void defects exist in the joints. © 2003 Elsevier B.V. All rights reserved.Keywords: Friction stir welding; Tensile properties; Welding p
9、arameter; Aluminum alloy; Fracture location1. IntroductionHeat-treatable aluminum alloys are difficult to fusion weld because some welding defects such as crack and porosity are easily formed in the weld during the solid
10、- ification of the welding pool [1]. Friction stir welding (FSW) is a solid phase welding process in which the metal to be welded is not melted during the welding, thus the crack and porosity often associated with fusion
11、 welding processes are eliminated [1,2]. Therefore, the FSW pro- cess can be used to weld heat-treatable aluminum alloys in order to obtain high-quality joints [1–4]. However, many studies on the microstructural characte
12、ristics and mechan- ical properties of the friction-stir-welded joints have in- dicated that FSW gives rise to softening in the joints of the heat-treatable aluminum alloys such as 2014-T651 [5], 2024-T3 [6,7], 2024-T351
13、 [8,9], 2024-T6 [10,11], 2195-T8 [12,13], 6061-T5 [14,15], 6061-T6 [8,16–18], 6063-T5 [19–21], 6082-T5 [22], 7075-T651 [23] and 7475-T76 [7] because of the dissolution or growth of strengthening pre-? Corresponding autho
14、r. Tel.: +81-6-6879-8663. E-mail addresses: lhj@jwri.osaka-u.ac.jp, liuhj@hope.hit.edu.cn (H.J. Liu).cipitates during the welding thermal cycle, thus resulting in the degradation of the mechanical properties of the joint
15、s. Hence, it is important to study the effects of welding pro- cess parameters on the mechanical properties of the joints and determine the optimum welding parameters so as to obtain high-quality friction-stir-welded joi
16、nts. In the 2xxx-series heat-treatable aluminum alloys, 2014-T651, 2024-T3, 2024-T351 and 2024-T6 were fric- tion stir welded in order to examine the tensile proper- ties [5–8,11] or fracture locations [5,7,8] of the joi
17、nts. The 2017-T351 aluminum alloy is one of the 2xxx-series heat-treatable aluminum alloys and it has not been friction stir welded up to now. This paper aims to demonstrate its friction stir weldability and the emphasis
18、 is placed on the relations of the tensile properties and fracture locations of the joints to the welding parameters in order to determine the optimum FSW parameters and find out the weakest locations of the joints.2. Ex
19、perimental procedureThe base material used in this study was a 2017-T351 alu- minum alloy plate of 5 mm thick, whose chemical compo- sitions and mechanical properties are listed in Table 1. The0924-0136/$ – see front mat
20、ter © 2003 Elsevier B.V. All rights reserved. doi:10.1016/S0924-0136(03)00806-9694 H.J. Liu et al. / Journal of Materials Processing Technology 142 (2003) 692–696RS AS00.10.20.3-15 -10 -5 0 5 10 15Distance from weld
21、 center, mmStrain0.02 mm/r 0.07 mm/r 0.27 mm/rFig. 2. Strain distributions in the typical joints.distributions of the joints welded at the different revolution- ary pitches. In this figure, the location at which the maxi
22、- mum strain of each joint occurs is the fracture location of the joint. In addition, the retreating side and advancing side of each joint are denoted by RS and AS, respectively. It is observed from Fig. 2 that the strai
23、n distributions of the joints are located in a comparatively narrow region and the strain values are considerably low. Especially, the fracture lo- cations of the joints are not distant from the weld center and change wi
24、th the revolutionary pitches. When the revolution- ary pitch is much smaller e.g. 0.02 mm/rev, the fracture loca- tion of the joint is only 4.1 mm from the weld center. When the revolutionary pitch increases to 0.07 mm/r
25、ev, the frac- ture location of the corresponding joint changes to 1.9 mm away. When the revolutionary pitch is equal to or greater than 0.27 mm/rev, the joints are all fractured at the weld cen- ter. That is to say, as t
26、he revolutionary pitch increases, the fracture location of the joint gradually approaches the weld center. These results indicate that the joints are fractured under the conditions of local and heterogeneous deformation,
27、 and the fracture locations of the joints are significantly affected by the welding parameters. Moreover, it should be noted that all the joints are fractured on the advancing side or at the weld center, but not on the r
28、etreating side of the joints. This implies that the tensile properties of the joints are not the same on the two sides of the weld center, and the tensileFig. 3. Cross-sections of the typical joints welded at the differe
29、nt revolutionary pitches: (a) 0.02 mm/rev; (b) 0.07 mm/rev; and (c) 0.27 mm/rev.RS AS 90110130150-20 -15 -10 -5 0 5 10 15 20Distance from weld center, mmVickers hardness, Hv0.02 mm/r 0.07 mm/r 0.27 mm/rFig. 4. Microhardn
30、ess distributions of the typical joints welded at the different revolutionary pitches.properties on the advancing side are weaker than those on the retreating side.3.2. DiscussionA softened region has been formed in the
31、joints of 2017-T351 aluminum alloy due to the effect of friction heat as occurred in the joints of other heat-treatable aluminum alloys [7,21–23]. The tensile properties and fracture loca- tions of the joints are, to a l
32、arge extent, dependent on the welding defects and hardness distributions of the joints, and which, in turn, on the welding parameters [6,11,14]. Figs. 3 and 4 show, respectively, the typical cross-sections and microhardn
33、ess distributions of the joints welded at the dif- ferent revolutionary pitches. When the revolutionary pitch is smaller than 0.13 mm/rev, FSW produces defect-free joints (see Fig. 3(a) and (b)). When the revolutionary p
34、itch is greater than 0.13 mm/rev, some void defects are formed in the joints because of the lack of heat input to the joints (see Fig. 3(c)). When such void defects exist in the joints, the tensile properties and fractur
35、e locations of the joints are significantly affected by the defects. In Fig. 4, the hardness values at the void locations do not exist and are expressed by “x”. These voids generally occur in the middle of the weld, thus
溫馨提示
- 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
- 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
- 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
- 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
- 5. 眾賞文庫僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
- 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
- 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。
最新文檔
- 外文翻譯--2017-t351鋁合金攪拌摩擦焊接頭的拉伸性能和斷裂位置
- 外文翻譯--2017-t351鋁合金攪拌摩擦焊接頭的拉伸性能和斷裂位置
- 外文翻譯--2017-t351鋁合金攪拌摩擦焊接頭的拉伸性能和斷裂位置(中文)
- 外文翻譯--2017-T351鋁合金攪拌摩擦焊接頭的拉伸性能和斷裂位置(中文).doc
- 外文翻譯--2017-T351鋁合金攪拌摩擦焊接頭的拉伸性能和斷裂位置(中文).doc
- 航空鋁合金攪拌摩擦焊接頭性能研究.pdf
- 6082-T6鋁合金攪拌摩擦焊接頭組織和性能的研究.pdf
- 紫銅及鋁合金攪拌摩擦焊接頭性能研究.pdf
- 高強鋁合金攪拌摩擦焊接頭的組織與性能.pdf
- 鋁合金攪拌摩擦焊接接頭組織及疲勞斷裂行為研究.pdf
- 鋁合金攪拌摩擦焊接頭微觀組織及性能研究.pdf
- 7050鋁合金攪拌摩擦焊接頭組織與性能研究.pdf
- 鋁合金攪拌摩擦焊接頭腐蝕行為研究.pdf
- 鋁合金攪拌摩擦點焊接頭動態力學性能研究.pdf
- 鋁合金攪拌摩擦焊接接頭應力腐蝕性能研究.pdf
- 高強鋁合金攪拌摩擦焊焊接接頭疲勞性能研究.pdf
- 7075鋁合金攪拌摩擦焊接頭疲勞性能評定和缺陷分析的研究.pdf
- 2060鋁合金攪拌摩擦焊接頭腐蝕機理.pdf
- 航空鋁合金Lc4-T4和7075-T6攪拌摩擦焊接頭疲勞性能研究.pdf
- 鋁合金攪拌摩擦焊接頭疲勞性能與工藝參數的關系.pdf
評論
0/150
提交評論