無線傳感器網絡的測距技術外文翻譯

1、<p><b>　　河北建筑工程學院</b></p><p>　　畢業設計（論文）外文資料翻譯</p><p>　　系別： 電氣系 </p><p>　　專業： 電子信息工程 </p><p>　　班級： 電子092班

2、 </p><p>　　姓名： 王成 </p><p>　　學號： 2009315213 </p><p>　　外文出處： Wireless.Sensor.Networks： </p><p>　　A.Networking.Perspective </

3、p><p>　　附 件：1、外文原文；2、外文資料翻譯譯文。</p><p><b>　　外文原文（復印件）</b></p><p>　　8.3 RANGING TECHNIQUES FOR WIRELESS SENSOR NETWORKS</p><p>　　The RF location sensors opera

4、ting in different environments can measure the RSS, AOA, phase of arrival (POA), TOA, and signature of the delay - power profile as location metrics to estimate the ranging distance [4,7] . The deployment environment (i.

5、e., wireless RF channel) will constrain the accuracy and the performance of each technique. In outdoor open areas, these ranging techniques perform very well. However, as the wireless medium becomes more complex, for exa

6、mple, dense urban or indoor env</p><p>　　The TOA based ranging is suitable for accurate indoor localization because it only needs a few references and no prior training. By using this technique, however, the

7、 hardware is complex and the accuracy is sensitive to the multipath condition and the system bandwidth. This technique has been implemented in GPS, PinPoint, WearNet, IEEE 802.15.3, and IEEE 802.15.4 systems. The RSS bas

8、ed ranging, on the other hand, is simple to implement and is insensitive to the multipath condition and the bandwi</p><p>　　This section first introduces TOA based ranging and the limitations imposed by the

9、wireless channel. Then it will be compared with the RSS counterpart focusing on the performance as a function of the channel behavior. What is introduced here is important to the understanding of the underlying issues in

10、 distance estimation, which is an important fundamental building block in WSN localization.</p><p>　　8.3.1 TOA Based Ranging</p><p>　　In TOA based ranging, a sensor node measures the distance to

11、 another node by estimating the signal propagation delay in free space, where radio signals travel at the constant speed of light. Figure 8.3 shows an example of TOA based ranging between two sensors. The performance of

12、TOA based ranging depends on the availability of the direct path (DP) signal [4,14] . In its presence, for example, short distance line - of - sight (LOS) conditions, accurate estimates are feasible [14] . The challenge,

13、</p><p>　　due to the multipath components (MPCs), which are delayed and attenuated replicas of the original signal, arriving and combining at the receiver shifting the estimate. The second is the propagation

14、 delay caused by the signal traveling through obstacles, which adds a positive bias to the TOA estimates. The third is the absence of the DP due to blockage, also known as undetected direct path (UDP) [14] . The bias imp

15、osed by this type of error is usually much larger than the first two and has a sign</p><p>　　In order to analyze the behavior of the TOA based ranging, it is best to resort to a popular model used to describ

16、e the wireless channel. In a typical indoor environment, the transmitted signal will be scattered and the receiver node will receive replicas of the original signal with different amplitudes, phases, and delays. At the r

17、eceiver, the signals from all these paths combine and this phenomenon is known as multipath. In order to understand the impact of the channel on the TOA accuracy, we </p><p>　　，（8.1）</p><p&g

18、t;　　where Lp is the number of MPCs, and , , and are amplitude, phase, and propagation delay of the kth path, respectively [7,23] . Let and denote the DP amplitude and propagation delay, respectively. The distance betwee

19、n the sensor node and the RP or anchor is , where v is the speed of signal propagation. In the absence of the DP, ranging can be achieved using the amplitude and propagation delay of the non - direct path (NDP) component

20、 given by and, respectively; resulting in a longer distance, whe</p><p>　　，（8.2）</p><p>　　must be less than the receiver dynamic range k and the power of the DP must be greater than the re

21、ceiver sensitivity . These constraints are given by </p><p>　　，（8.3a）</p><p>　　, （8.3b）</p><p><b>　　where. </b></p><p>　　In general,

22、ranging and localization accuracy is constrained by the ranging error, which is defined as the difference between the estimated and the actual distance; that is, .</p><p>　　.（8.4）</p><p&

23、gt;　　In an indoor environment, the node/MT will experience a varying error behavior depending on the availability of the DP and in the case of its absence on the characteristics of the DP blockage. It is possible to cate

24、gorize the error based on the following ranging states [24] . In the presence of the DP, both (8.3a) and (8.3b) are met and the distance estimate is very accurate, yielding </p><p>　　,（8.5a）</p>

25、<p>　　where the random bias induced by the multipath, is the bias corresponding to the propagation delay caused by NLOS conditions, and z is a zero - mean additive measurement noise. It has been shown that is in

26、deed a function of the bandwidth and the signal to noise ratio (SNR) [14] , while bpd is dependant on the medium of the obstacles.When the node experiences sudden blockage of the DP, Eq. (8.3a) is not met and the DP is s

27、hadowed by some obstacle, burying its power under the dynamic range of th</p><p>　　,（8.6a）</p><p>　　,（8.6b）</p><p>　　where is a deterministic additive bias represent

28、ing the nature of the blockage. Unlike the multipath biases, but similar to the biases induced by the propagation delay, the dependence of on the system bandwidth and SNR has its own limitations as reported in Ref. [14]

29、 . Formally, these ranging states can be defi ned as</p><p>　　,（8.7a）</p><p>　　,（8.7b）</p><p>　　Figures 8.4 and 8.5 provide sample channel profiles of these two ra

30、nging situations [24] . </p><p>　　The performance of TOA based ranging can be determined by the Cramer-Rao lower bound (CRLB), which has been studied extensively for existing systems. The variance of TOA est

31、imation is bounded by the CRLB [25] </p><p>　　,（8.8）</p><p>　　where T is the signal observation time, is the SNR, is the frequency of operation, and w is the system bandwidth. </p>

32、;<p>　　In practice, TOA can be obtained by measuring the arrival time of a wide-band narrow pulse, which can be obtained either by using spread spectrum technology or directly. </p><p>　　8.3.1.1 Direc

33、t Spread Spectrum.</p><p>　　One TOA estimation technique based on the direct spread spectrum (DSS) wideband signal has been used in GPS and other ranging systems for many years. In such a system, a signal co

34、ded by a known pseudorandom (PN) sequence is transmitted and a receiver cross - correlates the received signal with a locally generated PN sequence using a sliding correlator or a matched filter. The distance between the

35、 transmitter and the receiver is determined from the arrival time of the first correlation peak. Beca</p><p>　　8.3.1.2 Ultra - Wideband Ranging.</p><p>　　A promising alternative to DSS systems i

36、s ultra - wideband (UWB) ranging [26] . According to Eq. (8.8) , it is clear that in multipath propagation environments, the performance of TOA estimation is inversely related to the system bandwidth. Increasing the syst

37、em bandwidth (i.e., narrower time - domain pulse) results in higher time resolution and thus better ranging accuracy. As a result, these systems have attracted considerable attention in recent years [16,22,26] . For UWB

38、applications, the FC</p><p>　　One important observation from these measurement results is that higher bandwidths improve time - domain resolution, which resolves the pulse into respective components, resulti

39、ng in improved accuracy. The trade - off, however, is that higher resolution implies lower energy per MPC, which means a higher probability of DP blockage. This means that the ranging coverage of 500 - MHz systems is lar

40、ger than that of the 3 - GHz counterpart. Although UWB can reduce multipath significantly, combating th</p><p>　　2、外文資料翻譯譯文</p><p>　　8.3無線傳感器網絡的測距技術</p><p>　　射頻位置傳感器在不同的環境中運行可測量RSS，

41、AOA，階段的到來（POA），TOA，和作為位置的度量估計距離延遲功率譜 [4,7]。這種部署環境（例如，無線射頻信道）將限制精度和每種技術的性能。在戶外空曠地區，這些測距技術執行得很好。然而，隨著無線介質而變得更加復雜，例如，密集的城市或室內環境中，信道存在嚴重的多徑傳播和嚴重的陰影衰落環境。這一發現反過來說明了在一對節點之間的距離估計對精度和性能的影響。為此，本章將重點討論在室內環境中的測距和定位。這點很重要，因?yàn)樵S多WSN應用程序

42、設想在崎嶇的地形和雜亂的環境中部署傳感器，因此，對測距和定位性能的信道的影響的理解是很重要的。此外，采用POA和AOA在室內和城市地區進行測距是不可靠的。因此，我們將重點討論兩個實用技術，TOA和RSS。這兩種測距技術，已經有在無線網絡中使用的傳統，它們對于在無線傳感器網絡定位有著很大的潛力。</p><p>　　TOA測距適合于精確的室內定位是因?yàn)樗恍枰苌俚奈墨I(xiàn)并且不需要事先訓練。但是，通過使用這種技術，硬

43、件會變得復雜、精度的多徑條件和系統帶寬會敏感。這種技術已經被實施在GPS，PinPoint，wearnet，IEEE 802.15.3，和IEEE 802.15.4系統應用上。另一方面，RSS測量實現簡單，對多徑條件和系統的帶寬不敏感。此外，它不需要任何同步，可以與任何現有的無線系統協同工作，可以測量RSS。然而，對于準確的測量，錨或參考點的高密度是必要的，并且廣泛的培訓和昂貴的算法也是必需的。RSS測距已被用于在WiFi定位系統中，比

44、如Ekahau，Newbury Networks，Pango和Skyhook。</p><p>　　本章首先介紹了基于測距的TOA和所施加在無線通道的局限性。然后它與專注于信道行為函數的RSS的性能進行比較。這里所介紹的在測距基本問題上的認識很重要，這是研究無線傳感器網絡定位的重要基礎。</p><p>　　8.3.1 TOA測距</p><p>　　在TOA測距中

45、，傳感器節點到另一個節點間距離的測量是通過自由空間中的信號傳播時延來估計的，信號傳播在無線信號以光速為恒定速度。圖8.3展示了兩個節點間的TOA測距。 TOA測距的性能取決于直接路徑的可用性（DP）信號[ 14 ]。例如，在DP信號中，短距離的線的視線（LOS）的條件下，準確的估計是可行的[ 14 ]。然而，我們面臨的挑戰是，在非LOS（NLOS）表現為網站的特異性和密集多徑環境的條件下。這些環境提出了一些挑戰。</p>

46、<p>　　圖8.3 傳感器間的TOA測距</p><p>　　第一個由于多徑分量（MPC）所引起的腐化的TOA估計，這是原始信號延遲和衰減的復制品，到達和合并接收器的移動估計。第二個是由信號穿過障礙物引起的傳播延遲，這增加了一個正向偏置的TOA估計。第三是由于堵塞的DP的缺失，也被稱為未發現的直接路徑（UDP）[ 14 ]。這種類型的錯誤引起的偏壓通常是比前兩大得多，同時由于櫥柜，電梯，或通常在室

47、內門附近，也會引起更大出錯的概率。</p><p>　　為了分析基于TOA測距的行為,最好采取一個受歡迎的模型用來描述無線信道。在一個典型的室內環境中,傳輸信號將被分散，接收者節點將收到與原始信號不同振幅、階段和延誤的副本信號。在接收機,信號從所有這些路徑結合,這種現象稱為多徑。為了了解影響精度的渠道,我們常常借助于一個用于描述多路徑到達的模型。這個模型描述了多路徑通道,脈沖響應特征路徑,到達各自的振幅和延誤。在

48、數學上,它可以表示為一個求和的多路徑組件或到達</p><p>　　，（8.1）</p><p>　　其中，Lp代表MPCs的數量，，，分別是振幅，相位以及傳播延遲的路徑。讓和分別表示DP振幅和傳播延遲。傳感器節點之間的距離和RP或錨是,v是信號傳播的速度。在DP的缺席中,測距可以通過,分別由和給出的使用振幅和傳播延遲的非直接的路徑(NDP)組件來達到;這導致了長的距離,其中。

49、為使接收機識別DP,最大的MPC與DP信號的比例如下</p><p>　　，（8.2）</p><p>　　它必須低于接收機動態范圍k的能力并且DP必須大于接收機靈敏度。這些約束條件如下</p><p>　　，（8.3a）</p><p>　　,（8.3b）</p><

50、p><b>　　其中。</b></p><p>　　一般來說,測距和定位精度受到測距誤差的限制,其被定義為估計和實際的距離的差異;那就是</p><p><b>　?。?.4）</b></p><p>　　在室內環境中,節點/MT將會體驗一種取決于可用性的DP不同的錯誤行為和具有DP堵塞特征對于的缺席。它可能是基于以

51、下測距狀態[24] 的錯誤分類。在DP下, (8.3a)和(8.3 b)得到滿足和距離的估計是非常準確的。</p><p>　　，（8.5a）</p><p>　　其中，是在隨機偏差引起的多路徑, 是由NLOS引起的傳播延時的偏置, z是一個零,意味著添加劑測量噪聲。它已被證明的確是一個函數的帶寬和信號噪聲比(信噪比)[14],而bpd是依賴于介質的障礙。當節點經歷突然DP,

52、Eq阻塞,(8.3 a)不滿足和DP被一些障礙所阻擋,它將它的能量放在在動態范圍的接收機。在這種情況下,同Eq(8.5 a)相比，測距估計將會有一個更大的誤差范圍。其中值得強調的是，測距是通過NDP組件來實現的,然后由以下給出</p><p>　　圖8.4 寬帶在200MHz范圍的TOA估計</p><p>　　，（8.6a）</p><p>　　，

53、（8.6b）</p><p>　　是一個堵塞性質的確定性偏置。與多路徑偏置不同,但類似于由于傳播延遲引起的偏置，取決于系統帶寬的，并且信噪比都有自己的局限性上報信息[14]。一般來說，這些測距狀態可以被定義為</p><p>　　，（8.7a）</p><p>　　，（8.7b）</p><p>

54、　　圖8.4和8.5提供樣品通道配置文件的這兩個測距情況[24]。</p><p>　　基于TOA測距的性能范圍可以由最大下界(CRLB)確定,它已廣泛地用于研究現有系統。TOA測距中的估計由CRLB[25]確定</p><p>　　，（8.8）</p><p>　　圖8.5 在寬帶為200MHz范圍內的NDP的TOA測距</p><

55、p>　　其中T是信號的觀測時間, 是信噪比、是運作的頻率,w是系統帶寬。</p><p>　　在實踐中,可以通過測量獲得長遠的到達時間一個寬帶窄脈沖來獲得TOA,也可以通過使用或直接擴頻技術。</p><p>　　8.3.1.1直接擴頻</p><p>　　一種基于直接擴頻(DSS)寬帶信號的TOA測距技術已經應用于GPS和其他測距系統許多年了。在這樣一個系統

56、,一個由已知的偽隨機(PN)序列編碼的信號是用來傳播的和一個交叉關聯的接收器接收信號的與本地PN序列生成使用滑動相關器或一個匹配濾波器。發射機和接收機之間的距離是由到達時間的第一個相關峰確定。因?yàn)樘幚碓鲆娴南嚓P(guān)性在接收機、DSS測距系統在同一頻帶的性能遠遠好于競爭的系統抑制干擾其他無線電系統操作。在這些有限的系統中,超級分辨率技術已經成功應用于TOA測距。結果表明,這些高分辨率算法可以提供改善的準確性[25]。</p>&

57、lt;p>　　8.3.1.2超寬頻帶范圍。</p><p>　　一個有前途的可以用來替代DSS系統是超寬帶(UWB)測距[26]系統。很明顯,根據Eq. (8.8)，在多徑傳播環境,TOA測距的性能估計是逆相關系統帶寬。通過增加系統帶寬(即更窄的時間-域脈沖)導致更高的時間分辨率,從而有更好的測距精度。因此, 近年來這些系統已經引起了相當大的關注。對于超寬頻應用,FCC規定分配一個無照平頻帶3.1 - 10

58、.6 GHz,有兩個建議:直接序列(DS)——超寬頻和多頻帶正交頻分復用(MB - OFDM)。前者是基于脈沖,利用大帶寬,例如,3 GHz,而后者占有帶寬為528 MHz。這些系統的準確性的評估可以通過他們?cè)诙鄰叫诺赖男袨閬頇z查。在室內辦公環境的測量由圖8.6a的500 - MHz系統提供,類似于MB - OFDM渠道。8.6 b為3 GHz帶寬,類似于更廣泛的DS - UWB信道。在發射機和接收機預計到達時間是40.5 ns，500

59、 - MHz和3 – GHz的估計到達分別是45.5和40.7 ns。5 – 和0.2 - ns錯誤在TOA估計中分別導致1.67米和7 -厘米誤差,這清晰說明的影響系統精度更高的帶寬。</p><p>　　一個重要的發現是這些測量結果是高帶寬的改善時間-域分辨率,它解決了到各自組件的脈沖,從而提高精度。然而,反過來看，高分辨率便意味著較低的能量,這意味著MPC更高機率的DP堵塞。這意味著范圍覆蓋500 - MH